2 ohm sub hook up, how do you wire up a dual 4 ohm sub to 2 ohms

  1. Im trying to get my system planned out before I hook up all the gear.
  2. You need to wire both positives to one positive input and both negatives to one negative input for parallel wiring.
  3. These things are monsters, I'm having trouble finding an amp that can power these things without buying something that has way to much power.
  4. If so I am not sure of the wiring.
  5. It is freaking incredible.
  6. You should be fine hooking up one of your subs to each of that amp's channels.

Other than that, all I know is that it stays clean and has decent power. Should the Cap be wired before all the Amps or just the one pushing the subs? Right now the way i have it wired the amp will cut into protection mode if i have my volume turned too high. The best wiring diagram for dual core sub can be found in the accompanying link.

Hey Buck, I've got a question. And I don't want to fry my subs or amp any help would be appreciated. There is plenty of room and clearance. Will that give more power?

Not knowing exactly which you have makes it impossible to give advice on what amplifier to use. There are many ways to wire subwoofers and amplifiers together. You will need this wire to make the connections from your amplifier to your sub-woofers. Hey buck I have a pyramid pb watt amp with two Sony xplod subs and they are not hitting as hard as I think they should be could it be there not getting enough power?

Can i hook up my sub if it s wired to a 2 ohm and my amp is 4 ohm

How to Wire a 4 Ohm Amp to a 2 Ohm Speaker

The kenwood amp seems like its working hard because i can small a weird plastic smell when i run it for about ten minutes. Can any one give me any good suggestions. You'll need to wire the sub like this. The subs are in a sealed downfire box under the rear seat. It is greatly appreciated!

Wiring Subwoofers What s All This About Ohms

  • Aaron, If the specs you quote are correct, you can wire your gear together like this.
  • Not a clean crisp thump like I was hoping for.
  • How would you recommend wiring it all up if I have a sealed box that has a divider in the middle, with wiring terminals on the outside of the box?
  • Jedwards, I think that amplifier is woefully too weak to drive those subs properly.

What s the difference between a

The sub is rated at w rms. Is there any way you can resend the link? Do i have to bridge my Sub? If you want a question answered about your system, online dating wordpress you must identify your equipment not only by the brand name but also the model number. Do you have any input for this particular unit?

It ll work fine but there ain t no such thing as a free lunch

1 Suggested Answer

You are in line to receive a call from. Joe, Not knowing exactly what amplifier or subwoofers you have make it impossible to give advice on how to wire them together. Make sure you set the amp gain so no distortion ever plays. Is there possible wiring issues? The amplifier provides the power.

Hello my name is Scott and I don't know much about this stuff at all. The lower a speaker's impedance, the easier it is for an amp to supply power to it. Do you have any suggestions?

The amplifier sees the same load on its outputs and the subwoofers receive the same amount of power. Or does it supply each with w? Unfortunately, we're only licensed to sell gear in the United States and Canada. Or, use one positive and one negative amp terminal for the pair of subs, it doesn't matter which. Check to see which two terminals are used for bridge mode on your amplifier.

Those infinity speakers are amazing. The radio works with the carscomputer to reset codes and other stuff. When the impedances of all the devices are the same, their total impedance, when wired in parallel, is that impedance value divided by the number of devices. Matt, Wire that gear together like this diagram and rock on. If you plan on listening to music at moderate volume levels or have a smaller car, a subwoofer with a lower power handling rating, say to watts, and a matching amp is a good combo.

If you want a question answered about a system, dating coimbatore you must identify the equipment by brand names and model numbers. How can i wire them together to get the most powerful sound possible. Is this possible or recommended? When I get a chance I will break the bridge and run one channel to each voice coil.

How do you wire up a dual 4 ohm sub to 2 ohms

Like everyone else, I want all I can get out of the amp, but I don't want to burn it up. Can you please recommend the best Monoblock to drive these two subwoofers. Is there a better way to wire them up without hurting anything or am I better off eliminating a sub?

Add Your Answer

Hook all the negatives together, and hook all the positives together. Can you hook up a car sub system to a home stereo system? Can you hook up several speaker to the same port? Regardless of which combinations of series and parallels you chose above to get the proper impedance and power distribution in your system, closing the circuit will be one easy step. Resistance that is too low draws more power than the output is rated for.

And if so is that to much? What will be the best way to wire them. However, tay fm dating this rockford fosgate site does Is this accurate? And it's perfectly alright to have different brand speakers in the same system. Thank you so much for your future help.

2 channel bridged amp driving a 2 ohm load Pro Help Needed

Just make sure you set the amp gain so no distortion ever plays. What amplifier required for best effects? Dave, That sub will work fine with that amp, wired like this.

Mike, There is no electrical difference between those two wiring schemes. So I am looking at another sub or two. Do you have any recommendations on amps? Different ohm on each channel. Is this even possible and if so, how?

There is no requirement that a sub must be fed its exact power rating. Matt, It is safe to replace factory subs with aftermarket subs. You will have to re-drill the mounting screw holes. You should be alright as long as you never play distortion, trying to get louder bass.

Is mixed impedance a concern under the following configuration? Am I understanding this correctly? Ok so I've heard a lot of my buddies refer to you diagrams for wiring up subs and I've used them a few time to help. Now if only today weren't saturday.

2 channel bridged amp driving a 2 ohm load Pro Help Needed

Experiment and report back with the results. If you want accurate answers to your questions, you must identify your gear. If you want a question answered about a system, it's best that you identify the gear by brand names and model numbers. We have a wal-mart locally.

As for a diagram, I can point you to our Amplifier wiring diagrams. Also can I put two amp circuit breakers in to be safe? You can, but you may damage your amp. You should be alright, though, online dating how to say as long as you set the amp gain low enough to never play distortion. Click on this link for details.

How can you hook up a 2 ohm amplifier to a 4 ohm sub

Series Connections
  • Gratis dating site relatieklik nl
  • Who is kenya moore dating
  • Kent singles speed dating
  • Dating when you are a short guy
  • Dating in singapore services
  • Dating female marines
  • Wordpress dating site theme
  • Nphc dating